Download BUILD A REMOTECONTROLLED ROBOT DAVID R SHIRCLIFF by David R. Shircliff PDF

By David R. Shircliff

TAB Electronics is the most effective identify in beginner robotics. because the 1987 free up of Gordon McComb's blockbuster robotic Builder's Bonanza hobbyists have seemed to TAB because the resource for state-of-the-art, how-to robotics titles.
These groundbreaking, seriously illustrated books clarify tips on how to create everythinbg from easy, basic robots to ones that stroll, see, consider, speak, pay attention and struggle! Written via "professors of robotics" resembling Gordon McComb and John Iovine, they're nice for newcomers in addition to skilled robotic builders.
Authoritative, cutting edge, enjoyable, and continuously some distance prior to someone else, TAB keeps the culture with construct your individual Remote-Controlled robotic.

Show description

Read Online or Download BUILD A REMOTECONTROLLED ROBOT DAVID R SHIRCLIFF PDF

Similar robotics & automation books

Hard Disk Drive: Mechatronics and Control

The harddrive is among the best examples of the precision regulate of mechatronics, with tolerances lower than one micrometer accomplished whereas working at excessive velocity. expanding call for for better facts density in addition to disturbance-prone working environments proceed to check designers mettle.

Robot Modeling and Control

In a well timed topic, arrived a couple of week after i ordered it and the ebook is in strong conition.

LEGO MINDSTORMS NXT-G Programming Guide (Technology in Action)

LEGO Mindstorms NXT is the preferred robotic out there. James Kelly is the writer of the most well-liked weblog on NXT (http://thenxtstep. blogspot. com/) with over 30,000 hits a month. The NXT-G visible programming language for the NXT robotic is totally new and there are at present no books to be had at the topic.

Identifikation dynamischer Systeme: Methoden zur experimentellen Modellbildung aus Messdaten

Das Werk gibt eine ausführliche Einführung in die Identifikation linearer und nichtlinearer Ein- und Mehrgrößensysteme. Es werden zahlreiche Identifikationsverfahren vorgestellt, mit denen aus gemessenen Ein- und Ausgangssignalen ein mathematisches Modell zur Beschreibung des Systemverhaltens ermittelt werden kann.

Extra resources for BUILD A REMOTECONTROLLED ROBOT DAVID R SHIRCLIFF

Sample text

1-10 shows how to do this. After you find the center point, place the castor wheel on the platform so that if turned in a circle, the wheel will not protrude past the front edge of the platform. Next mark and drill the hole for the wheel’s mounting plate. (The diameter of the 10 CHAPTER ONE TABLE 1-1. Parts List ITEM AMOUNT 2 Motorized wheel 1 Sheet of 24- ϫ 24- ϫ 1/4-inch plywood 1 4-inch-diameter castor wheel 8 2-inch ϫ 1/4-inch-diameter bolt, nut, and lockwasher set 4 3-inch ϫ 1/4-inch-diameter bolt, nut, and lockwasher set 2 2-inch ϫ 3/4-inch-diameter bore washer 1 Auto fiberglass repair kit, including cloth and resin 1 Can spray paint (color of your choice) FIGURE 1-10.

FIGURE 2-4. Drilling and cutting guide. FIGURE 2-5. Drilling and cutting guide. FIGURE 2-6. Drilling and cutting guide. FIGURE 2-7. Drilling and cutting guide. BODY FRAMEWORK 19 FIGURE 2-8. Drilling and cutting guide. that piece. The figures depict each piece as if it were laid lengthwise with its two edges on a workbench then flattened so both sides could be seen. All the figures show the locations and diameter of the holes to be drilled. The locations of the 45-degree angle cuts to be made at the ends of many of the aluminum pieces are shown as shaded areas where the aluminum is to be removed.

Table 2-2 is for the upper section and Table 2-3 is for the lower section. BODY FRAMEWORK 31 FIGURE 2-25. Drilling and cutting guide. After you have matched the pieces, line up the predrilled 1/8-inch holes at the ends of each piece. If the holes on the pieces do not line up (which happened to me three-quarters of the time), clamp them together and redrill the 1/8-inch-diameter hole in both pieces at the same time. Next insert a 1/8-inch rivet into the hole and using a rivet gun “pop” the rivet to secure the pieces.

Download PDF sample

Rated 4.80 of 5 – based on 47 votes